Archive for February, 2012

« Older Entries

Melbourne Village Air Conditioning Guide: What to Do Before Turning on AC for First Time

Wednesday, February 29th, 2012

The weather is starting to heat up and you are eager to flip the switch on your Melbourne Village home’s air conditioning system for the first time. It’s been sitting there last summer, waiting to be used, but now you wonder if there are any tasks that should be completed before its first use. Depending on the type of system you had installed there are a few things you should keep in mind before you cool down your house. They include:

  • Outdoor Cleaning – First, make sure the outdoor unit (if you have a central AC system) is cleaned up nicely. Clear away any leaves, remove the cover and check the system for any growth or debris that might have gotten under the cover. Check the air supply registers to make sure they are open and either replace or clean your filters depending on whether they are permanent or disposable.
  • Check Your Thermostat – The thermostat should be checked before you start using the system. To do this, set the system to Auto-cool and then lower the thermostat setting to one degree lower than the actual temperature in the room. If the system turns on, the thermostat is working properly. Let it run for a few hours to make sure this stays consistent.
  • Clear Away Winter Dust – Now that your system is running, make sure you check the filters for any buildup of dust that was in the ductwork. Over the off season, your ducts might develop a layer of dust and debris, especially if your heating system doesn’t make use of them. The filters might clog quickly as a result.
  • Check for Water Leaks – Your condensate overflow drain should work properly as well – check for any potential leaks during the first 48 hours of operation. Even a small leak should be checked immediately to avoid potential problems as summer cooling season kicks in.

If you notice any problems other than those listed above, you should call a service professional immediately. Ideally you will have your system inspected in early-mid spring to ensure it is ready for the summer, but even so problems can develop between inspection and first running. Electrical issues especially should be checked immediately. If you would like your system examined before you turn it on for the first time, give Next Generation Air & Heating a call!

Tags: , , , , ,
Posted in Services | Comments Off

Grant Energy Saving Tip: Common Causes of Drafts in Your Home

Friday, February 24th, 2012

If you find your Grant home’s heating or cooling bill is routinely too high, there is a common reason. Most of the time it is due to air leaks and drafts in your home that allow warm air to escape and cold air to enter and vice versa. Here are some common causes of such leaks and what you can do about them.

Sources of Drafts in Your Home

There are obvious drafts and less obvious ones. Let’s start by looking at the drafts that are most obvious:

  • Outlets and Plates
  • Windows
  • Baseboards
  • Attic
  • Air Conditioners
  • Weather Stripping

You can probably do a quick inspection of your home by yourself to check for these potential air leaks and find whatever may be causing the problem. The easiest way to check for drafts is simply to hold your hand up to the space and check for a change in air flow. You can also get a portable thermometer and see if the air temperature is different in those areas than it is in the center of the room or by the thermostat.

Insulation Inspection

Insulation is probably already in your home, but with time it can thin, get leaks or tear. Look for gaps in insulation or drafts coming through. A professional can inspect your insulation as well and make sure that it is still holding as much heat in as it was originally rated for. If you know that your insulation values are too low or that the insulation is particularly old, it may be a good time to have it replaced.

Making Changes

If you notice easy to fix drafts in your home, fix them immediately and you’ll be shocked by how much energy you save. For larger leaks such as your insulation, loose windows or problems with your doors, consider calling someone who is an expert in closing up air drafts and keeping your home both comfortable and affordable to heat and cool.

To learn more ways to keep your home comfortable this year, give Next Generation a call today!

Tags: , , , ,
Posted in Services | Comments Off

Barefoot Bay Heat Pump Maintenance Tips: What Happens When You Neglect Maintenance

Wednesday, February 22nd, 2012

Just like any HVAC system, the heat pump in your Barefoot Bay home needs routine maintenance and yearly check-ups to operate as efficiently and safely as possible. You also don’t want your heat pump to wear down to the point of a major malfunction or breakdown, which can be costly to repair or may require a complete system replacement.

Here are some things that could go wrong and cost you a lot more in the end if you don’t keep up with the regular maintenance of your heat pump.

Damage to the Compressor

The compressor in a split-system heat pump works whether you are heating or cooling your home. In the winter, the compressor reverses the flow of the refrigerant to defrost the outdoor coils, and in the summer it supplies the refrigerant to cool the home, as well as cooling the outdoor coils. Proper airflow is vital to keeping the compressor running smoothly. Filters that are not changed regularly, dirty coils, and dirty fans can all restrict airflow, which will damage the compressor. Debris around the outside components should also be cleared to allow proper airflow.

Decreased Efficiency

When dirty or broken components restrict the airflow, this damages the compressor and decreases the heat pump’s efficiency levels.  Not only is it important to clean your heat pump regularly, but you should also have it checked by a certified heating technician once a year. This will also prevent safety hazards and other hidden issues with the heat pump.

Improper Refrigerant Levels

Most heat pumps are charged with refrigerant at the factory; however, if models that are charged when they are installed are not given the right amount of refrigerant this can also affect performance levels. Refrigerant leaks and other common problems can be prevented by scheduling an annual maintenance visit with one of our qualified technicians.

Don’t wait until the heat pump in your Barefoot Bay home stops working, call Next Generation Air and Heat today to schedule your yearly check-up.

Tags: , , , , ,
Posted in Services | Comments Off

Happy President’s Day from Your Central Florida Heating and Air Conditioning Contractors!

Monday, February 20th, 2012

Everyone at Next Generation wishes you a happy President’s Day! Today we appreciate all of the great leaders that helped shape our nation. Whether you have the day off today or not, it is a good time to think about how you can help make community a better place. From volunteering to recycling, helping improve your town can be pretty simple. Remember that upgrading your HVAC system can cut down on the amount of fuel you need to keep your home comfortable, and making your home more environmentally friendly is something that helps everyone.

Here is some great trivia about our presidents in honor of this day:

  • The only president who never married
    •  James Buchanan
  • Number of presidents who never attended college
    • Nine (Washington, Jackson, Van Buren, Taylor, Fillmore, Lincoln, A. Johnson, Cleveland, and Truman)
  • Number of presidents who died in office
    •  Eight (Harrison, Taylor, Garfield, Lincoln, McKinley, F.D. Roosevelt, Kennedy)
  • Presidents Portrayed on US coins
    • Lincoln (penny)
    • F.D.  Roosevelt (dime)
    • Kennedy (half-dollar)
    • Eisenhower (dollar coin)
    • Jefferson (nickel)
    • Washington (quarter)
  • Presidents Portrayed on US Currency
    • Washington (one dollar bill)
    • Jefferson (two dollar bill)
    • Lincoln (5 dollar bill)
    • Hamilton (10 dollar bill)
    • Jackson (20 dollar bill)
    • Grant  (50 dollar bill)
    • Franklin (100 dollar bill)

Have a great President’s Day!

Tags: ,
Posted in Services | Comments Off

Maitland Whole House Air Quality Systems: Why You Need One

Friday, February 17th, 2012

There are many ways to control the indoor air quality of your Maitland home. The easiest way to is to clean your vents and ducts. This reduces the number of pollutants like mold and dust that get into your air each day. In some cases, however, you may need something more powerful and that’s where a whole house air quality system comes in.

What Does Whole House Air Quality Provide?

There are many filters and purifiers on the market that can be operated in a single room such as your living room or the bedroom of your child. However, if you have a more substantial contaminant problem, a whole house system actually attaches to the source of fresh air.

Most whole house systems integrate directly into the ventilation ducts and fans of your house. This ensures the air is purified and cleaned as it enters your home, not after it has circulated for some time. Air cleaners are also integrated into ducts where UV lighting and ionizers can remove bacteria, viruses, smoke and exhaust fumes that come in from outside.

Your furnace and air conditioner will also be filtered above and beyond standard manufacturer filtering, ensuring there are less contaminants traveling through your ducts to start with.

When Do You Need It?

The upgrade to a whole house system isn’t just for those suffering from dust, pollen and pet dander. These can easily be removed with regular cleaning of your ducts and a HEPA filter in each room affected. However, if your home tests high for various gases, exhaust fumes, or molds that are beyond your control, a whole house system is a great way to protect yourself.

In particular, these systems are useful when the contaminants come in from outside. Most indoor contaminants can be removed with careful maintenance of your comfort system, but if your neighbor has a leaky exhaust pipe or if you live near a busy highway, you can’t do much about it other than to filter the air as it comes inside.

Choosing a whole home air quality system starts with knowing what you need to filter. So, proper air testing is highly recommended. After testing, make sure your current systems will integrate well with the new air quality controls. If everything works properly, you’ll be well on your way to fresh, clean air in no time. If you have any questions about your Maitland home’s indoor air quality system, give Next Generation Air & Heat a call!

Tags: , , , ,
Posted in Services | Comments Off

Happy Valentine’s Day from Your Central Florida Heating and Air Conditioning Contractor!

Tuesday, February 14th, 2012

Everyone at Next Generation Air and Heat wishes you a very Happy Valentine’s Day! We hope your day is full of love and laughter! Valentine’s Day is a time to really appreciate all of the wonderful people in your life, including your significant other, your family, and your friends. Take a moment today to let each of them know how special they are to you. Even something simple, like a handmade card, can really make someone’s whole day!

While your HVAC system might not seem like the most romantic place to start your gift giving, a few simple upgrades can make your house more comfortable, which is something your whole family will appreciate! A HEPA filter can keep dust and allergens out of your air, and a new furnace or heat pump can keep your house at more consistent temperatures and cut down on your energy use. An upgrade to your HVAC system is truly a gift that keeps on giving!

For more information about easy ways to improve your home, give Next Generation Air and Heat a call! And to help make your Valentine’s Day as happy as it can be, here is a recipe for Chocolate Covered Strawberries:

“This is the simplest version of chocolate covered strawberries I know. Paraffin was originally used instead of shortening. Turn the strawberries upside down and insert by the toothpicks into a piece of styrofoam for easy cooling, or simply place them on a sheet of wax paper. White chocolate may be drizzled over the milk chocolate for a fancier look. They are perfect for weddings when decorated with frosting bow ties, bells, butterflies, roses, etc.”

INGREDIENTS:

16 ounces milk chocolate chips

2 tablespoons shortening

1 pound fresh strawberries with leaves

DIRECTIONS:

  1. Insert toothpicks into the tops of the strawberries.
  2. In a double boiler, melt the chocolate and shortening, stirring occasionally until smooth. Holding them by the toothpicks, dip the strawberries into the chocolate mixture.
  3. Turn the strawberries upside down and insert the toothpick into styrofoam for the chocolate to cool.

For more details, visit allrecipes.com.

Tags: , , ,
Posted in Services | Comments Off

Sebastion Indoor Air Quality Advice: Sick Building Syndrome

Monday, February 13th, 2012

When you buy a house in Sebastion, you assume that it’s safe to live in. You assume that the construction is sound and the air quality is good so that you never need to worry about things like excessive illness due to contamination. However, the World Health Organization estimates that nearly 30% of homes built in the 1980s subjected homeowners to Sick Building Syndrome – a situation where indoor air quality causes symptoms and feelings of illness without a clear cause.

That number has dropped in the last 25 years as many homes have been remodeled and retrofitted to stay comfortable year round, but without proper air quality control, a home with poor ventilation and filtration may still be unsafe.

How Do I Know We Have Sick Building Syndrome?

There are quite a few potential symptoms of poor air quality and SBS in your home. Chest tightness and coughing is a primary factor and can lead to fevers and chills. Often, recovery from the illness has nothing to do with your health, but with the conditions of your home – you may not feel better until repairs are completed or you leave the house.

Other symptoms of sick building syndrome include headache, eye and nose irritation, dry skin, nausea and dizziness, fatigue and trouble concentrating. And throughout it all, your doctor likely won’t be able to determine the cause of your discomfort.

What Causes This

The most common reason for sick building syndrome is poor ventilation. In the 1970s, the ventilation requirements for new homes were reduced by 66% to help save energy. However, air quality measures were not included to ensure people stayed healthy. That has since changed as ASHRAE, the American Society of Heating, Refrigerating and Air Conditioning Engineers raised the recommendations back to the pre-1973 levels and even increased them in some cases.

There are other things as well you should look out for including indoor chemical exposure to carbon monoxide from exhaust fans, nitrogen dioxide, and formaldehyde. Outdoor sources can make you ill as well. Smoke, exhaust, and various gases from outside your home can enter your indoor air and cause illness to your family if they aren’t properly filtered out.

Finally, there are things like mold, bacteria and pollen which are always issues for indoor air. Proper purification and filtration will help with each of these problems, but only if you monitor and test for them regularly. If you have any concerns about your home’s indoor air quality, call Next Generation Air and Heat today!

Tags: , , ,
Posted in Services | Comments Off

Palm Shores Heat Pump Tip: Outdoor Maintenance

Friday, February 10th, 2012

Sometimes, the trickiest part about owning a heat pump in Palm Shores  is keeping the outdoor components maintained. Because they are outside and generally out of sight, it can be easy to forget or neglect them. But because they are outside and exposed to the elements, outdoor heat pump components need attention and maintenance to keep them running properly.

The two most important routine maintenance functions you can do as an owner of an outdoor heat pump are keeping it free of debris and keeping it level.

Every month or so, inspect and clean your outdoor heat pump to make sure it is free of leaves, dirt and other debris. These can easily be sucked in by the fan and reduce the efficiency of the whole system. Turn the power off to the unit and use a vacuum or broom to remove any accumulated debris.

Once or twice a year, use a carpenter’s level to make sure the whole thing is sitting level on the pad. Use the level to gauge both side to side and front to back. While you are doing this, check the insulation for erosion or gaps. If you see that it is not level or the insulation is wearing thin, have a contractor come out reset the unit on the concrete pad or patch up the insulation.

These are two small maintenance tasks that you don’t have to do very often, but they can make a big difference in the performance and life of your heat pump.

In addition, you should always have your whole heating, ventilation and cooling system inspected by a Palm Shores professional, like Next Generation Air and Heat, annually in order to keep everything maintained and in good repair.

Tags: , , , , ,
Posted in Services | Comments Off

Cape Canaveral Heat Pump Repair Guide: How to Handle Your Finicky Heat Pump

Wednesday, February 8th, 2012

A heat pump is designed to keep your Cape Canaveral comfortable. Warm weather, cold weather – it doesn’t matter. It should turn on when you need it and turn off when you don’t. So, when the device starts turning on and off without reason or when you need it to stay on, what exactly is the problem and how can you fix that problem without losing the heating or cooling capacity of your device.

 Common Causes of the Problem

There are a number of reasons why your heat pump would turn off shortly after turning on, and most of the time this occurs in heating mode. If it occurs in cooling mode, you should have the device inspected immediately because there is likely something wrong with a core component like the compressor. For heating mode issues, here are some common problems:

  • Dirty Coils – If the coils are dirty, the device won’t be able to properly operate, especially if it has been some time since the last cleaning. Both sets of coils need to be cleaned at least once a year to avoid this becoming a problem.
  • Low Refrigerant Charge – If the refrigerant gets low, you’ll need to have it recharged because the pressure in the device will drop and it will therefore turn off after a few minutes of use.
  • Defrost Timer – If the defrost timer is forcing the device into a defrost cycle too often (usually it is set to 30, 60, or 90 minutes), the fan might turn off every few minutes after turning on. This is a common problem and is usually due to a thermostat or switch issue which can be fixed relatively easily.

Another thing to ask yourself when this problem occurs is whether the device is heating properly when on. Defrost timer issues don’t usually impinge on the heating ability of the device, while low refrigerant can. You want to make sure the device is working properly when on and not just cycling on and off without heating capacity.

Based on what you find, you’ll need a technician to take a closer look and ensure everything is working properly. Most repairs for this type of problem are relatively simple.

Tags: , , , , ,
Posted in Services | Comments Off

Cocoa Beach Heat Pump Repair Tip: Heat Pump Blowing Cold Air in Winter

Monday, February 6th, 2012

One of the most impressive things about a heat pump is that it can both cool and heat your Cocoa Beach home. But, if something goes wrong and your heat pump is suddenly trying to cool your home in the middle of the winter, you have a problem. Here are some possible causes of the issue and what you can do about them.

 Defective Reversing Valve

The reversing valve is responsible for changing the flow of refrigerant between seasons so your heat pump can both heat and cool your home. So, if it breaks, you can imagine what happens next – you won’t switch into heating mode and your heat pump will try to air condition your home.

Defective reversing valves are hard to diagnose because the symptoms are largely the same as those of a defective compressor or condenser valve. However, because of how they are installed and where they are located, you will need a professional to inspect this problem no matter what.

 Low on Refrigerant

Your heat pump should never run low on refrigerant because it shouldn’t leak, but if it does and the refrigerant gets low or if your device is simply very old, this may be a problem. Low refrigerant means that the device cannot transfer enough heat between the outdoor air and the inside air and the air that gets blown through your ducts by the air handler isn’t heated as much as is necessary to warm your house.

The problem is relatively easy to fix, though you should also have your repairman check for leaks and a possible cause of the refrigerant being low in the first place.

 Not Running at All

The final problem is one you should be able to notice quite easily. If the heat pump isn’t working at all but the air handler and blower are working fine, then the device will simply blow cold air from outside or possibly even just recycled cold air from inside. In either case, the heat pump isn’t running to heat the air and therefore, you’re getting whatever temperature it is outside.

This can be caused by a number of problems so it’s important to call Next Generation Air and Heat to inspect it immediately.

Tags: , , , , ,
Posted in Services | Comments Off

« Older Entries